Free Declaration in Support - District Court of California - California

Case 5:07-cv-05248-JW
P R O D U C

Document 154-3
T I N F

Filed 05/19/2008
O R M A

Page 1 of 14
T I O N

Information about Dow Corning ® Brand Adhesive/Sealants
Silicones and Electronics
Archeological evidence shows that adhesives have been in use for over 6000 years, and many objects can be seen in museums that are still bonded with adhesives after 3000 years or more. While you may not need that extreme of long-term, reliable protection, you still want your adhesive to outlast your device. While our track record may not be thousands of years old, we have been making adhesives for electronics almost since their inception. Many Dow Corning products have been in continuous use for 30 years or more and are still being applied today, testifying to the suitability of silicone adhesives for electronics. Silicones have long been known for durable dielectric insulation, as barriers against environmental contaminants and for their stress-relieving shock and vibration absorption. They can sustain their physical and electrical properties over a wide range of temperature, humidity and other harsh environmental conditions. Developments over the years have allowed Dow Corning to add special properties to this durable material foundation in response to your needs. Some of the more recent developments include: · Fast tack-free · Lower volatility · Faster or lower temperature cure · Adhesion to difficult current and future substrates · Less inhibition in heat-cure adhesives · Curable pressure-sensitive adhesives Some of the applications with special needs for which we are currently developing materials include: · PDP and LCD terminal sealing · Automotive electronics module and sensor sealing · Power supply and SMPS adhering · Electrical instrument adhering and sealing · Circuit board laminating and adhering Heat Cure Dow Corning addition-curing adhesives should be cured at 100°C (212°F) or above. The cure rate is rapidly accelerated with heat (see cure schedules in table). For thicker sections or if voiding is observed, use of one of the newer lowvoiding adhesives or a 30-minute pre-cure at 70°C (158°F) may reduce voids in the elastomer. Addition-curing materials contain all the ingredients needed for cure with no byproducts from the cure mechanism. Deep-section or confined cures are possible. Cure progresses evenly throughout the material. These adhesives generally have long working times. Dow Corning® brand Adhesives are supplied in three product forms: One-Part Moisture Cure RTV Dow Corning one-part moisture cure adhesives are generally cured at room temperature and in a range of 30 to 80 percent relative humidity. Greater than 90 percent of their full physical properties should be attained within 24 to 72 hours depending on the product chosen. Materials and parts can be handled in much shorter times of about 10 to 120 minutes depending on the product chosen and the amount of material used per part. These materials are not typically used for highly confined or deep section cures. Materials will generally cure about 0.25 inch per seven days from any exposed surface. Cure progresses from the outer surface and is dependent on the moisture in the air. Working time is generally a few minutes to an hour for these products until a surface skin begins to form. Mild heat acceleration of the cure rate may be possible, but temperatures above 60°C (140°F) are not recommended. Two-Part Room Temperature Condensation Cure Dow Corning two-part RTV adhesives cure rapidly at room temperature after mixing. Good strength is attained within an hour but full properties are not reached for a number of days. These adhesives contain their own source of moisture, and cure progresses evenly throughout the material. Deep-section or confined cures are possible; however, some limitations exist. Refer to the "Reversion" section of this datasheet for additional information. Working time is only a few minutes.

GLEW EXHIBIT B

Case 5:07-cv-05248-JW

Document 154-3

Filed 05/19/2008

Page 2 of 14

Custom Solutions
Fast Formulation Dow Corning manufactures a wide variety of adhesives to meet the needs of most application and process situations, and we are continuously expanding the product offerings in each of these families to ensure that there are products to meet your needs. However, if you cannot find a match for your needs, Dow Corning can modify any of our existing products to help meet your exact needs through our Fast Formulation process. A few examples of how Fast Formulation can help meet your exact needs include: modification of product cure schedule, modulus, viscosity or color, or adding/removing an inert intermediate such as UV indicator ­ all in a timely manner. Total Support Product Finder ­ Dow Corning features a unique interactive product finder on our website. This tool can help you pick the right materials for your applications; you can access the product finder at www.dowcorning.com/electronics and selecting "Technical Details" on any of our product family pages. Production of Prototype Coated Boards or Process Design We can produce sample parts, boards or test coupons and patterns for early evaluation of an adhesive's abilities and adhesives can be applied simulating your own process. Based on our extensive industry experience, we can advise you on the best methods and conditions for your process. Analytical, Environmental and Physical Testing We have expertise to share on a wide range of testing to monitor quality, for specialized testing for trouble-shooting, or to simulate accelerated service conditions. Equipment Recommendations Over many years of providing materials for electronics protection, Dow Corning has developed strong alliances with key equipment suppliers worldwide. We have just launched the External Equipment Provider Alliance with nine leading companies. Save time and expense by taking advantage of these alliances to ensure the optimum integration of material and processing. Consultation with Technical Experts Have our experts visit your facility or join us at one of our global application centers to work together on your material and processing needs. We can provide seminars and training for your personnel to allow them to work more knowledgably. With material, process and equipment integration solutions from Dow Corning, you can manufacture more modules and assemblies in less time, at less cost, with fewer shutdowns and fewer customer rejects.
2

Tutorials An adhesive tutorial can be found on our web site. It is accessible from the product family pages or the left hand navigation bar under Technical Library.

Product/Application Information
PREPARING SURFACES All surfaces should be thoroughly cleaned and/or degreased with Dow Corning® brand OS Fluids, naphtha, mineral spirits, methyl ethyl ketone (MEK) or other suitable solvent. Solvents such as acetone or isopropyl alcohol (IPA) do not tend to remove oils well, and any oils remaining on the surface may interfere with adhesion. Light surface abrasion is recommended whenever possible, because it promotes good cleaning and increases the surface area for bonding. A final surface wipe with acetone or IPA is also useful. Some cleaning techniques may provide better results than others; users should determine the best techniques for their particular applications. ADHESION Dow Corning silicone adhesives are specially formulated to provide unprimed adhesion to many reactive metals, ceramics and glass, as well as to selected laminates, resins and plastics. However, good adhesion cannot be expected on nonreactive metal substrates or non-reactive plastic surfaces such as Teflon®, polyethylene or polypropylene. Special surface treatments such as chemical etching or plasma treatment can sometimes provide a reactive surface and promote adhesion to these types of substrates. Dow Corning® brand Primers (see "Primer Selection Guide", page 12) can be used to increase the chemical activity on difficult substrates. Poor adhesion may be experienced on plastic or rubber substrates that are highly plasticized, because the mobile plasticizers act as release agents. Small-scale laboratory evaluation of all substrates is recommended before production trials are made. In general, increasing the cure temperature and/or cure time will improve the ultimate adhesion. SUBSTRATE TESTING Due to the wide variety of substrate types and differences in substrate surface conditions, general statements on adhesion and bond strength are impossible. To ensure maximum bond strength on a particular substrate, 100 percent cohesive failure of the adhesive in a lap shear or similar adhesive strength test is desired. This ensures compatibility of the adhesive with the substrate being considered. Also, this test can be used to determine minimum cure time or can detect the presence of surface contaminants such as mold release agents, oils, greases and oxide films.

GLEW EXHIBIT B

Case 5:07-cv-05248-JW

Document 154-3

Filed 05/19/2008

Page 3 of 14

USEFUL TEMPERATURE RANGES For most uses, silicone elastomers should be operational over a temperature range of -45 to 200°C (-49 to 392°F) for long periods of time. However, at both the low- and hightemperature ends of the spectrum, behavior of the materials and performance in particular applications can become more complex and require additional considerations. For low-temperature performance, thermal cycling to conditions such as -55°C (-67°F) may be possible, but performance should be verified for your parts or assemblies. Factors that may influence performance are configuration and stress sensitivity of components, cooling rates and hold times, and prior temperature history. At the high-temperature end, the durability of the cured silicone elastomer is time and temperature dependent. As expected, the higher the temperature, the shorter the time the material will remain useable. COMPATIBILITY Certain materials, chemicals, curing agents and plasticizers can inhibit the cure of addition cure adhesives. Most notable of these include: · Organotin and other organometallic compounds · Silicone rubber containing organotin catalyst · Sulfur, polysulfides, polysulfones or other sulfurcontaining materials · Amines, urethanes or amine-containing materials · Unsaturated hydrocarbon plasticizers · Some solder flux residues If a substrate or material is questionable with respect to potentially causing inhibition of cure, it is recommended that a small scale compatibility test be run to ascertain suitability in a given application. The presence of liquid or uncured product at the interface between the questionable substrate and the cured gel indicates incompatibility and inhibition of cure. MIXING AND DE-AIRING Upon standing, some filler may settle to the bottom of the liquid containers after several weeks. To ensure a uniform product mix, the material in each container should be thoroughly mixed prior to use. Two-part materials should be mixed in the proper ratio (1:1 or 10:1) either by weight or volume. The presence of light colored streaks or marbling indicates inadequate mixing. Automated airless dispense equipment can be used to reduce or avoid the need to de-air. If de-airing is required to reduce voids in the cured elastomer, consider a vacuum de-air schedule of >28 inches Hg for 10 minutes or until bubbling subsides.
3

One-Part Moisture Cure RTV Type
Noncorrosive, one or two-part moisture curing RTV silicone elastomers; cure at room temperature without the need for heat

Physical Form

Nonflowing and flowable options; cures to a flexible elastomer

Special Properties

Room temperature cure; opaque and translucent options; resists humidity and other harsh environments; good dielectric properties; good adhesion to a variety of common substrates; low stress, low volatility with some being fast tack-free; two-part materials can also offer rapid cure and green strength at room temperature and deep section cure

Potential Uses

Sealing modules and housings; gasketing; sealing of electronic equipment and modules; part fixing on circuit boards of power supply and CRT, LCD/LED/PDP module assembly, housing, gasketing, attaching electronic parts

Two-Part Room Temperature Condensation Cure Type
Two-part RTV silicone elastomers

Physical Form

Nonflowing; cures to a flexible elastomer

Special Properties

Rapid cure and green strength at room temperature; deep section cure; resists humidity and other harsh environments; good dielectric properties; self-priming adhesion; low stress

Potential Uses

Lid and housing seals; gasketing

Heat Cure Type
One- and two-part silicone elastomers provided in a wide variety of as-applied and as-cured forms

Physical Form

Non-flowing and flowable options; cures to a flexible elastomer; wide variety of cured forms and properties available

Special Properties

Fast thermal cure at lower temperature; resists humidity and other harsh environments; good dielectric properties; selfpriming adhesion; low stress, less voiding during curing

Potential Uses

Lid and housing seals; seals for ECUs, power modules; fixing electronics parts to circuit boards; reinforcing or fixing parts of connectors; gasketing electronics parts/modules; sealing condensers and electronics components; fixing flyback transformers

GLEW EXHIBIT B

Case 5:07-cv-05248-JW

Document 154-3

Filed 05/19/2008

Page 4 of 14

PRODUCT INFORMATION
Dow Corning® Brand Product Description Features Potential or Typical Uses One-Part Moisture Cure RTV EA-3000 White 1-part, white, fast tackfree Fast tack-free; low viscosity; noncorrosive (alcohol type RTV); excellent adhesion to most materials; self-priming; excellent dielectric properties; excellent thermal stability and cold resistance; low volatility Fast tack-free time; noncorrosive; controlled volatility LCD & EL module assembly

SE 9120 Clear

1-part, flowable; translucent, moisture cure RTV 1-part, flowable, white, moisture cure RTV

EL, LCD module assembly, hybrid IC and PCB coating, encapsulation of electrical devices EL, LCD module assembly Sealing of sheathed heater terminations Sealing of electronic equipment and modules; parts fixing on circuit board Parts fixing on circuit board; LCD module assembly

SE 9120 S White SE 9152 HT SE 9186 Clear or White SE 9186 L Black or L Clear SE 9187 L Black or L Clear or L White 3140 RTV Coating

Fast tack-free time; noncorrosive; controlled volatility

1-part, flowable, reddish Fast tack-free time; noncorrosive; heat resistance to brown, moisture cure RTV 275°C 1-part, flowable, translucent or white, moisture cure RTV 1-part, flowable, black or translucent, moisture cure RTV 1 part, low viscosity, black, translucent or white, moisture cure RTV 1-part, moderate flow, translucent, moisture cure RTV 1-part, moderate flow, gray or white, moisture cure RTV 1-part, moderate flow, translucent, moisture cure RTV 1-part, nonflow, white, moisture cure RTV Fast tack-free time; noncorrosive; controlled volatility

Fast tack-free time; noncorrosive; controlled volatility

Fast tack-free time; noncorrosive; controlled volatility; UL 94HB (black only) Noncorrosive; good cured strength; contains UV indicator for automated inspection; UL 94V-1 and MILA-46146 Fast tack-free time; noncorrosive; controlled volatility; UL V-0 Fast tack-free time; contains UV indicator; UL 94V-0 and MIL-A-46058 Noncorrosive; general purpose; UL 94HB Noncorrosive; general purpose; good adhesion ; UL 94V-0 Noncorrosive; fast tack-free time; general purpose; good adhesion Noncorrosive; general purpose; UL 94HB

LCD module assembly; LED module assembly; potting Sealing lids and housings where grooves or other configurations support a flowable material or where limited flow is desired PDP module assembly; parts fixing on circuit board

SE 9189 L Gray or L White RTV 3-1944 RTV Coating SE 738 White 739 Plastic Adhesive ­ White 744 RTV Sealant 838 Silicone Adhesive/Sealant

Sealing lids and housings where grooves or other configurations support a flowable material or where limited flow is desired Fixing capacitors of coils to circuit board Wedge bonding or CRT; parts fixing of power supply module Bonding of large components such as batteries or capacitors to circuit boards Sealing openings in modules and housings; adding mechanical stability to individual components; assembly of components on PWBs; sealing in and around wired and electrical leads; yoke assembly Sealing openings in modules and housings; adding mechanical stability to individual components; assembly of components on PWBs; sealing in and around wired and electrical leads; yoke assembly Sealing openings in modules and housings; adding mechanical stability to individual components; assembly of components on PWBs; sealing in and around wired and electrical leads; yoke assembly

839 Silicone Adhesive/Sealant

1-part, nonflow, translucent blue, moisture cure RTV 1-part, nonflow, translucent, moisture cure RTV 1-part, nonflow, gray, moisture cure RTV 1-part, nonflow, gray, moisture cure RTV 1-part, nonflow, gray, moisture cure RTV 1-part, nonflow, white, moisture cure RTV

Noncorrosive; general purpose

3145 RTV MIL-A46146 Adhesive/ Sealant ­ Clear 3145 RTV MIL-A46146 Adhesive/ Sealant ­ Gray 3165 Fast Tack RTV Adhesive/ Sealant1 SE 9168 RTV SE 9184 White RTV SE 9185 Clear or White SE 9188 RTV SE 9189 White RTV 6-1104 CV Sealant 6-1125 CV Sealant
1

Noncorrosive; high tensile strength, elongation, peel and lap shear values, contains UV indicator for automated inspection; MIL-A-46146 Noncorrosive; high tensile strength, elongation, peel and lap shear values, good for high-temperature applications; MIL-A-46146 Fast tack-free time; noncorrosive; good green strength; good room-temperature adhesion to most substrates; UL 94V-0 Fast tack-free time; noncorrosive; controlled volatility; UL 94V-0 Fast tack-free time; noncorrosive; controlled volatility; thermally conductive; UL 94V-0

Parts fixing on CRT, circuit board of power supply modules Parts fixing on circuit board of power supply modules; heat transmission for electronics parts Sealing of electronic equipment and modules; parts fixing on circuit board Parts fixing on CRT, circuit board of power supply modules Parts fixing on circuit board of power supply modules Space-grade sealing and adhering

1-part, nonflow, translucent Fast tack-free time; noncorrosive; controlled volatility or white, moisture cure RTV 1-part, nonflow, gray, moisture cure RTV 1-part, nonflow, white, moisture cure RTV Fast tack-free time; noncorrosive; controlled volatility; UL 94V-0 Fast tack-free time; noncorrosive; controlled volatility; UL 94V-0; good thermal conductivity

1-part, nonflow, translucent, Low-volatility space-grade material moisture cure RTV 1-part, nonflow, white, moisture cure RTV

Not available in Europe.

4

GLEW EXHIBIT B

Case 5:07-cv-05248-JW

Document 154-3

Filed 05/19/2008

Page 5 of 14

PRODUCT INFORMATION (Continued)
Dow Corning® Brand Product CY 51-019 Description 2-part, 10:1 mix ratio, white, condensation cure RTV 2-part, 10:1 mix ratio, black, condensation cure RTV 2-part, 10:1 mix ratio, flowable, gray, heat cure 1-part, flowable, gray, heat cure 2-part, 10:1 mix ratio, flowable, beige, heat cure 1-part, flowable, beige, heat cure 1-part, flowable, beige or black, heat cure 2-part, 1:1 mix ratio, white, low void, fast cure, CV grade 1-part, flowable, white, heat cure 1-part, thixotropic, gray, heat cure 1-part, low void, black, flowable 1-part, low void, black, nonflow 1-part, good flow, black, heat cure 1-part, good flow, gray, heat cure 2-part, 10:1 mix ratio, low viscosity, heat cure 2-part, 1:1 mix ratio, moderate flow, black, heat cure 1-part black heat cure, moderate flow, high strength, similar to Q36611 Adhesive with UV indicator, self-priming 1-part, moderate flow, black, heat cure 1-part, moderate flow, gray, heat cure 2-part, 1:1 mix ratio, moderate flow, gray, heat cure Noncorrosive; self-priming; high strength Noncorrosive; self-priming; heat cure; high strength; low viscosity Noncorrosive; rapid low-temperature cure; flowable to allow channel filling; contains UV indicator for automated inspection Noncorrosive; self-priming; rapid heat cure; high strength; flowable; contains UV indicator for automated inspection Fixing components; bonding to various substrates such as ceramics, plastics, glass and metals Sealing lids and housings; attaching baseplates; gasketing; connector sealing Sealing lids and housings; attaching baseplates; gasketing; connector sealing; engine control; ABS; transmission; lighting Noncorrosive; self-priming; high strength; non-slump Features Noncorrosive; good flow; good adhesion Potential or Typical Uses Solar cell sealing

Two-Part Room Temperature Condensation Cure

Q3-6093 RTV Adhesive Kit Heat Cure Sylgard® 577 Primerless Silicone Adhesive Kit 866 Primerless Silicone Adhesive SE 1701 LTV1 SE 17131 SE 1714 or SE 1714 Black1 SE 1720 CV1

Noncorrosive; self-priming; rapid room temperature and deep section cure; good green strength; good room-temperature adhesion to most substrates Noncorrosive; rapid heat cure; self-priming; high strength; UL 94V-0; MIL-PRF-23586F Noncorrosive; self-priming; high strength Noncorrosive; self-priming; high strength Noncorrosive; self-priming; high strength; good adhesion

Sealing lids and housings; attaching baseplates; gasketing

Sealing lids and housings; attaching baseplates; gasketing, connector sealing Sealing lids and housings; attaching baseplates; gasketing, connector sealing Sealing ceramic condensers; sealing electronic components; bonding agent for key pad of PC Sealing lids and housings for ECUs, power modules; fixing electronics parts to circuit boards; reinforcing or fixing parts of connectors

SE 1750 White1

Noncorrosive; self-priming; good strength; good adhesion Self-priming; soft High-performance version of 3-1598 especially minimizing voids High-performance version of 3-6265 especially minizing voids Noncorrosive; self-priming; rapid heat cure; high strength; lower viscosity version of Q3-6611 Adhesive

Sealing lids and housings for ECUs, power modules; fixing electronics parts to circuit boards; reinforcing or fixing parts of connectors Sealing lids and housings; attaching baseplates; gasketing; connector sealing; engine control; ABS; transmission; lighting

3-1595 Silicone Adhesive 3-1598 HP 3-6265 HP 3-6876 Black Adhesive 3-6876 Gray Adhesive 96-083 Silicone Adhesive Kit EA-6052 Fast Low-Temp Cure Adhesive Kit X3-1598 Adhesive

Q3-6611 Adhesive, Black Q3-6611 Adhesive, Gray Q5-8401 Adhesive Kit

Noncorrosive; self-priming; rapid heat cure; high strength

EA-6054 Thixotropic 2-part, 1:1 mix ratio, Fast Low-Temp nonflow, black, heat cure Cure Adhesive Kit SE 1700 Clear1 2-part, 10:1 mix ratio, nonflow, translucent, heat cure 2-part, 10:1 mix ratio, nonflow, white, heat cure 2-part, 10:1 mix ratio, non-slump, white, heat cure 1-part, nonflow, black, heat cure

Noncorrosive; rapid low-temperature cure; non-slump; Sealing lids and housings; attaching baseplates; contains UV indicator for automated inspection gasketing; multiple plane dispensing Noncorrosive; self-priming; high strength Sealing ceramic condensers; sealing electronic components; bonding agent for key pad of PC Sealing ceramic condensers; sealing electronic components; bonding agent for key pad of PC Sealing ceramic condensers; sealing eletronic components; bonding agent for key pad of PC Sealing lids and housings; attaching baseplates; gasketing; connector sealing

SE 1700 White1 Q1-9225 Silicone Adhesive Kit 3-6265 Thixotropic Adhesive

Noncorrosive; self-priming; high strength Self-priming; high strength

Noncorrosive; self-priming; rapid heat cure; high strength; non-flowing version of Q3-6611 Adhesive; contains UV indicator for automated inspection

5

GLEW EXHIBIT B

Case 5:07-cv-05248-JW

Document 154-3

Filed 05/19/2008

Page 6 of 14

TYPICAL PROPERTIES ­ PHYSICAL
Specification Writers: Please contact your local Dow Corning sales office or your Global Dow Corning Connection before writing specifications on this product.
Extrusion Rate1, g/min Tensile Strength Elongation, percent Viscosity/Flowability, cps or mPa.sec

One- or Two-Part

Dow Corning® Brand Product EA-3000 White SE 9120 Clear SE 9120 S White SE 9152 HT SE 9186 Clear or White SE 9186 L Black or L Clear SE 9187 L Black or L Clear or L White 3140 RTV Coating SE 9189 L Gray or L White RTV 3-1944 RTV Coating SE 738 White 739 Plastic Adhesive ­ White 744 RTV Sealant 838 Silicone Adhesive/ Sealant 839 Silicone Adhesive/ Sealant 3145 RTV MIL-A-46146 Adhesive/Sealant ­ Clear 3145 RTV MIL-A-46146 Adhesive/Sealant ­ Gray 3165 Fast Tack RTV Adhesive/Sealant3 SE 9168 RTV SE 9184 White RTV SE 9185 Clear or White SE 9188 RTV SE 9189 White RTV 6-1104 CV Sealant 6-1125 CV Sealant
1

One-Part Moisture Cure RTV 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 White Translucent White Reddish Brown Translucent or White Black or Translucent Black or Translucent or White Translucent Gray or White Translucent White White White White Translucent Blue Translucent Gray Gray Gray White Translucent or White Gray White Translucent White 1,100 8,200 8,200 11,000 63,000 25,000 1,100 31,000 22,000 60,000 Nonflow Nonflow Nonflow Nonflow Nonflow Nonflow Nonflow Nonflow Nonflow Nonflow Nonflow Nonflow Nonflow NA NA NA NA NA NA NA NA NA NA -- -- -- 220 220 110 145 200 -- -- -- -- -- 18 A 23 A 23 A 30 A 20 A 25 A 17 A 31 A 32 A 29 A 33 A 24 A 39 A 28 A 28 A 45 A 49 A -- 46 A 72 A 31 A 37 A 73 A 45 210 210 230 300 230 60 450 270 -- 360 200 380 230 250 940 1030 170 520 420 400 400 470 0.3 1.4 1.4 1.6 2.1 1.6 0.4 3.1 1.9 -- 2.5 1.4 2.6 1.6 1.7 6.5 7.1 1.2 3.6 2.9 2.8 2.8 3.2 3 15 15 16 21 16 4 32 19 -- 25 14 27 16 18 66 72 12 37 30 28 28 33 100 420 420 250 490 320 170 420 250 -- 410 500 630 430 350 660 670 180 300 70 530 350 60 1.00 1.05 1.05 1.06 1.04 1.02 1.00 1.03 1.19 1.03 1.05 1.40 1.40 1.02 1.02 1.10 1.11 1.28 1.32 2.22 1.05 1.29 1.70

Contact customer service for product details Contact customer service for product details

Measured at 90 psi (6.2 bar) through a 1/8" (3.18 mm) orifice. 2 Cure time: 3-mm thickness, 20°C, 55% MRH. 3 Not available in Europe.

6

GLEW EXHIBIT B

Specific Gravity

Durometer

kgf/cm2

Color

MPa

psi

Case 5:07-cv-05248-JW

Document 154-3

Filed 05/19/2008

Page 7 of 14

Unprimed Adhesion Lap Shear Shelf Life from Date of Manufacture, months 15 at <32°C 15 at <32°C 15 at <32°C 12 at <32°C 15 at <32°C 15 at <32°C 12 at <32°C 12 at <32°C 15 at <32°C 12 at <30°C 24 at <32°C 15 at <27°C 12 at <30°C 24 at <32°C 24 at <32°C 12 at <32°C 12 at <32°C 12 at <32°C 15 at <32°C 7 at <25°C 15 at <32°C 15 at <32°C 15 at <25°C Linear Coefficient of Thermal Expansion, micron/m °C or ppm -- -- -- -- -- -- -- 315 -- -- -- -- -- 380 300 370 -- 250 -- -- -- -- -- Working Time, RT Room Temp Cure Time, hr

Heat Cure Time

RT Tack-Free Time, minutes

Dow Corning® Brand Product One-Part Moisture Cure RTV EA-3000 White SE 9120 Clear SE 9120 S White SE 9152 HT SE 9186 Clear or White SE 9186 L Black or L Clear SE 9187 L Black or L Clear or L White 3140 RTV Coating SE 9189 L Gray or L White RTV 3-1944 RTV Coating SE 738 White 739 Plastic Adhesive ­ White 744 RTV Sealant 838 Silicone Adhesive/ Sealant 839 Silicone Adhesive/ Sealant 3145 RTV MIL-A-46146 Adhesive/Sealant ­ Clear 3145 RTV MIL-A-46146 Adhesive/Sealant ­ Gray 3165 Fast Tack RTV Adhesive/Sealant SE 9168 RTV SE 9184 White RTV SE 9185 Clear or White SE 9188 RTV SE 9189 White RTV 6-1104 CV Sealant 6-1125 CV Sealant

-- NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA

8 9 9 16 9 8 9 70 9 13 100 30 30 45 35 55 75 4 6 2 5 9 8

-- 24 24 24 48 48 48 72 72 24 72(2) 72
(2)

-- NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA

-- 50 50 80 230 160 40 -- 200 -- 80 140 -- 140 140 -- -- 200 300 300 210 260 250

-- 40 (GL) 40 (GL) 55 (GL) 160 (GL) 115 (GL) 30 (GL) -- 140 (GL) -- 55 (AL) 100 (GL) -- 95 95 -- -- 140 210 (GL) 205 (GL) 145 (GL) 180 (GL) 175 (GL)

-- 3.9 3.9 5.6 16.1 11.5 3.1 -- 14.4 -- 5.7 10.0 -- 9.8 9.5 -- -- 14.0 21.4 20.9 14.8 18.4 18.0

48 48 48 48 48 24 48 48 48 48 72

Contact customer service for product details Contact customer service for product details

7

GLEW EXHIBIT B

kgf/cm2

N/cm2

psi

Case 5:07-cv-05248-JW

Document 154-3

Filed 05/19/2008

Page 8 of 14

TYPICAL PROPERTIES ­ PHYSICAL (continued)
Specification Writers: Please contact your local Dow Corning sales office or your Global Dow Corning Connection before writing specifications on this product.
Elongation, percent Tensile Strength One- or Two-Part Extrusion Rate,4 g/min Viscosity/ Flowability, Mixed or A/B, cps or mPa.sec

Dow Corning® Brand Product

Two-Part Room Temperature Condensation Cure CY 51-019 Q3-6093 RTV Adhesive Kit Heat Cure Sylgard® 577 Primerless Silicone Adhesive Kit 866 Primerless Silicone Adhesive SE 1701 LTV SE 1713
5 5

2 2

White Black

11,000 Nonflow

NA --

34 A 42 A

160 250

1.1 1.7

11 18

200 220

1.27 1.37

2 1 2 1 1 2 1 1 1

Gray Gray White Beige Beige or Black White White Gray Black

66,000 47,000 80,000 80,000 60,000 85,000 65,000 570,000 86,000

NA NA NA NA NA NA NA NA NA

63 A 56 A 64 A 61 A 65 A -- 66 A 60 OO 57 A

950 930 1000 1070 1030 460 920 240 780

6.6 6.4 6.9 7.4 7.1 3.2 6.3 1.7 5.4

67 65 70 75 72 32 65 17 55

200 210 200 220 250 360 120 800 260

1.29 1.31 -- 1.25 1.30 1.06 1.50 1.06 1.31

SE 1714 or SE 1714 Black5 SE 1720 CV5 SE 1750 White5 3-1595 Silicone Adhesive 3-1598 HP

3-6265 HP 3-6876 Black Adhesive 3-6876 Gray Adhesive 96-083 Silicone Adhesive Kit EA-6052 Fast Low-Temp Cure Adhesive Kit X3-1598 Adhesive Q3-6611 Adhesive, Black Q3-6611 Adhesive, Gray Q5-8401 Adhesive Kit EA-6054 Thixotropic Fast Low-Temp Cure Adhesive Kit SE 1700 Clear5 SE 1700 White5 Q1-9225 Silicone Adhesive Kit 3-6265 Thixotropic Adhesive
4 5

1 1 1 2 2 1 1 1 2 2 2 2 2 1

Black Black Gray Translucent Black Black Black Gray Dark Gray Black Translucent White White Black

400,000 37,000 36,000 9,000 41,000/ 51,000 84,000 85,000 85,000 120,000/ 63,000 290,000/ 300,000 Nonflow Nonflow Nonflow Nonflow

NA NA NA NA NA NA NA NA NA NA -- -- -- 85

71 A 53 A 54 A 56 A 56 A 60 A 60 A 60 A 60 A 63 A 46 A 46 A 46 A --

870 -- 800 840 770 820 840 850 870 800 1000 1000 1000 680

6.0 -- 5.5 5.8 5.3 5.7 5.8 5.9 6.0 5.5 6.9 6.9 6.9 4.7

61 -- 56 59 54 58 59 60 61 56 70 70 70 48

150 -- 260 120 150 220 230 240 200 170 420 420 420 180

1.31 -- 1.31 1.08 1.09 1.32 1.31 1.31 1.31 1.29 -- -- _ 1.35

Measured at 90 psi (6.2 bar) through a 1/8" (3.18 mm) orifice. Not available in Europe.

8

GLEW EXHIBIT B

Specific Gravity

Durometer

kgf/cm2

Color

MPa

psi

Case 5:07-cv-05248-JW

Document 154-3

Filed 05/19/2008

Page 9 of 14

Linear Coefficient of Thermal Expansion, micron/ m °C or ppm

Unprimed Adhesion Lap Shear Working Time, RT Room Temp Cure Time, hr Heat Cure Time RT Tack-Free Time, minutes

Dow Corning® Brand Product

Two-Part Room Temperature Condensation Cure CY 51-019 Q3-6093 RTV Adhesive - Kit Heat Cure Sylgard® 577 Primerless Silicone Adhesive Kit 866 Primerless Silicone Adhesive SE 1701 LTV SE 1713 SE 1714 or SE 1714 Black SE 1720 CV SE 1750 White 3-1595 Silicone Adhesive 3-1598 HP >12 hr NA 6 hr NA NA 6 hr NA NA -- NA NA NA NA NA -- NA NA -- NA NA NA NA NA -- NA NA -- 60 min @ 125°C 60 min @ 150°C 30 min @ 150°C 30 min @ 150°C 30 min @ 150°C 120 min @ 80°C, 60 min @ 100°C 30 min @ 150°C <60 min @ 125°C 180 min @ 100°C, 30 min @ 125°C, 15 min @ 150°C 35 min @ 100°C, 7 min @ 125°C, 5 min @ 150°C -- 30 min @ 150°C, 60 min @ 125°C -- 60 min @ 90°C, 30 min @ 125°C, 10 min @ 150°C 30 min @ 150°C, 60 min @ 125°C -- 30 min @ 150°C, 60 min @ 125°C 90 min @ 120°C 60 min @ 90°C, 30 min @ 125°C, 10 min @ 150°C 30 min @ 150°C 30 min @ 150°C 30 min @ 150°C 60 min @ 125°C, 30 min @ 150°C 880 700 820 740 750 220 500 230 820 605 480 570 (AL) 510 (AL) 520 (AL) 155 345 (AL) 160 570 61.9 48.9 57.9 52.0 53.0 15.9 35.4 16.3 58.1 300 360 -- -- -- -- -- -- 275 12 at <32°C 12 at <30°C 14 at <30°C 8 at <10°C 9 at <10°C 9 at <32°C 8 at <10°C 12 at <5°C 6 at <5°C 4 hr 32 min NA -- 24 1.5 NA NA 120 230 80 (AL/GL) 160 8.4 16.5 -- 285 12 at <32°C 12 at RT

3-6265 HP 3-6876 Black Adhesive 3-6876 Gray Adhesive 96-083 Silicone Adhesive Kit EA-6052 Fast Low-Temp Cure Adhesive Kit X3-1598 Adhesive Q3-6611 Adhesive, Black Q3-6611 Adhesive, Gray Q5-8401 Adhesive Kit EA-6054 Thixotropic Fast Low-Temp Cure Adhesive Kit SE 1700 Clear SE 1700 White Q1-9225 Silicone Adhesive Kit 3-6265 Thixotropic Adhesive

-- NA NA -- 304 min NA NA NA 9 min 115 min 8 hr 8 hr 8 hr NA

-- NA NA NA NA NA NA NA NA NA NA NA NA NA

-- NA NA NA NA NA NA NA NA NA NA NA NA NA

870 620 620 NA 730 (AL) 790 820 800 760 780 (AL) 420 420 420 550 (AL)

605 430 430 -- 500 545 570 550 530 535 290 (AL) 290 (AL) 290 (AL) 380

61.8 43.6 43.9 -- 51.2 55.5 58.0 56.2 53.9 54.6 29.5 29.5 29.5 39.0

265 -- -- -- 290 -- 260 255 -- 250 -- -- -- 270

12 at <5°C 12 at <4°C 12 at <32°C 12 at <40°C 12 at <5°C 12 at <4°C 12 at <4°C 12 at <50°C 12 at <40°C 18 at <30°C 18 at <32°C 12 at <30°C 12 at <5°C

9

GLEW EXHIBIT B

Shelf Life from Date of Manufacture, months 6 at <5°C

kgf/cm2

N/cm2

psi

Case 5:07-cv-05248-JW

Document 154-3

Filed 05/19/2008

Page 10 of 14

TYPICAL PROPERTIES ­ ELECTRICAL
Specification Writers: Please contact your local Dow Corning sales office or your Global Dow Corning Connection before writing specifications on this product.
Dielectric Strength Dielectric Constant Dissipation Factor Volume Resistivity, ohm-cm Agency Listing NA NA NA NA NA NA UL 94HB black only UL 94V-1/ MIL-A-46146 UL 94V-0 UL 94V-0/ MIL-A-46058 UL 94HB UL 94V-0 NA UL 94HB NA MIL-A-46146 MIL-A-46146 UL 94V-0 UL 94V-0 UL 94V-0 NA UL 94V-0 UL 94V-0

At 100 kHz

At 100 kHz

At 100 Hz

At 100 Hz

volts/mil

At 1MHz

Dow Corning® Brand Product One-Part Moisture Cure RTV EA-3000 White SE 9120 Clear SE 9120 S White SE 9152 HT SE 9186 Clear or White SE 9186 L Black or L Clear SE 9187 L Black or L Clear or L White 3140 RTV Coating SE 9189 L Gray or L White RTV 3-1944 RTV Coating SE 738 White 739 Plastic Adhesive ­ White 744 RTV Sealant 838 Silicone Adhesive/Sealant 839 Silicone Adhesive/Sealant 3145 RTV MIL-A-46146 Adhesive/ Sealant ­ Clear 3145 RTV MIL-A-46146 Adhesive/ Sealant ­ Gray 3165 Fast Tack RTV Adhesive/ Sealant1 SE 9168 RTV SE 9184 White RTV SE 9185 Clear or White SE 9188 RTV SE 9189 White RTV 6-1104 CV Sealant 6-1125 CV Sealant
1

475 575 575 625 575 575 500 445 625 425 500 625 400 500 480 500 500 500 650 500 550 750 800

19 23 23 25 23 23 20 18 25 17 20 25 16 20 19 20 20 20 26 20 22 30 31

-- -- -- -- -- -- -- 2.52 -- 2.67 -- -- -- 2.64 2.51 2.83 -- 2.22 -- -- -- -- --

-- -- -- -- -- -- -- 2.52 -- 2.73 -- -- -- 2.63 2.49 2.83 -- 2.38 -- -- -- -- --

2.8 2.7 2.7 2.6 2.8 2.7 2.8 -- 3.1 -- 2.8 3.5 -- -- -- -- -- -- 3.2 3.9 2.8 3.4 3.2

-- -- -- -- -- -- -- 0.004 -- 0.001 -- -- -- <0.001 <0.001 <0.001 -- 0.003 -- -- -- -- --

-- -- -- -- -- -- -- 0.0010 -- <0.0002 -- -- -- 0.0010 <0.0002 0.0010 -- 0.0010 -- -- -- -- --

9.00E-04 4.00E-04 4.00E-04 1.00E-03 9.00E-04 1.30E-03 9.00E-04 -- 4.00E-04 -- 7.00E-04 4.00E-03 -- -- -- -- -- -- 2.00E-03 2.00E-03 7.00E-04 3.00E-04 1.40E-03

At 1MHz

kV/mm

1.0E+15 7.0E+15 7.0E+15 3.0E+16 2.0E+16 6.0E+15 3.0E+15 2.1E+14 9.0E+14 1.3E+15 3.0E+15 2.0E+15 1.1E+15 2.2E+15 2.5E+14 4.4E+14 -- 2.4E+15 8.0E+15 1.5E+15 2.0E+16 1.0E+15 2.3E+15

Contact customer service for product details Contact customer service for product details

Not available in Europe.

10

GLEW EXHIBIT B

Case 5:07-cv-05248-JW

Document 154-3

Filed 05/19/2008

Page 11 of 14

TYPICAL PROPERTIES ­ ELECTRICAL (continued)
Specification Writers: Please contact your local Dow Corning sales office or your Global Dow Corning Connection before writing specifications on this product.
Dielectric Strength Dielectric Constant Dissipation Factor Volume Resistivity, ohm-cm Agency Listing NA NA UL 94V-0/ MIL-PRF-23586F NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA

At 100 kHz

At 100 kHz

At 100 Hz

At 100 Hz

volts/mil

At 1MHz

Dow Corning® Brand Product

Two-Part Room Temperature Condensation Cure CY 51-019 Q3-6093 RTV Adhesive - Kit Heat Cure Sylgard® 577 Primerless Silicone Adhesive Kit 866 Primerless Silicone Adhesive SE 1701 LTV1 SE 17131 SE 1714 or SE 1714 Black1 SE 1720 CV1 SE 1750 White1 EA-6052 Fast Low-Temp Cure Adhesive Kit EA-6054 Thixotropic Fast Low-Temp Cure Adhesive Kit 3-1595 Silicone Adhesive 3-1598 HP X3-1598 Adhesive 3-6265 HP Q3-6611 Adhesive, Black Q3-6611 Adhesive, Gray 3-6876 Black Adhesive 3-6876 Gray Adhesive Q5-8401 Adhesive Kit 96-083 Silicone Adhesive Kit SE 1700 Clear1 SE 1700 White1 Q1-9225 Silicone Adhesive Kit 3-6265 Thixotropic Adhesive 500 500 725 750 750 650 700 575 550 -- 500 -- 600 350 350 525 525 350 450 20 20 29 30 30 26 28 23 22 -- 20 -- 24 14 14 21 21 14 18 2.83 -- -- -- -- -- -- 3.06 3.08 -- 3.09 -- 3.14 3.09 3.02 2.81 2.81 -- -- -- -- -- 2.94 2.78 -- -- -- -- -- -- 3.01 3.02 -- 3.03 -- 3.09 3.02 2.95 2.78 2.78 -- -- -- -- -- 2.89 -- -- 3 3 3.1 2.7 3.2 -- -- -- -- -- -- -- -- -- -- -- -- 3 3 3 -- 0.006 -- -- -- -- -- -- 0.002 0.002 -- 0.006 -- 0.005 0.012 0.012 0.008 0.008 -- -- -- -- -- 0.009 0.0004 -- -- -- -- -- -- <0.0002 <0.0002 -- 0.0003 -- 0.0019 0.0038 0.0031 0.0010 0.0010 -- -- -- -- -- 0.0010 -- -- 3.00E-03 3.00E-03 2.80E-03 2.00E-03 2.00E-03 -- -- -- -- -- -- -- -- -- -- -- -- 1.00E-03 1.00E-03 1.00E-03 -- 1.3E+15 2.0E+15 1.0E+15 5.0E+15 5.0E+15 3.0E+16 9.0E+14 5.3E+14 2.8E+14 -- 4.5E+14 -- 9.2E+14 1.6E+14 1.6E+14 1.0E+14 1.0E+14 8.8E+14 1.7E+15 500 500 20 20 -- 3.38 -- 3.26 3.1 -- -- 0.009 -- 0.0026 4.00E-03 -- 4.0E+12 7.3E+14

550 550 550 525

22 22 22 21

At 1MHz

kV/mm

5.0E+14 5.0E+14 5.0E+14 4.7E+14

11

GLEW EXHIBIT B

Case 5:07-cv-05248-JW

Document 154-3

Filed 05/19/2008

Page 12 of 14

REVERSION When two-part condensation curing materials with organotin catalysts, such as Dow Corning® Q3-6093 RTV Adhesive, are cured in confinement (especially in deep section) and are later subjected to high heat conditions, they can potentially revert from a cured elastomer to a flowable polymer. Although this condition is unusual, parts using two-part condensation cure adhesives should be thoroughly tested in accelerated temperature conditions for this potential limitation. SOLVENT EXPOSURE The silicone adhesives discussed in this brochure are intended only to survive splash or intermittent exposures to liquid or vapor solvent or fuel that may occur in an application. These adhesives are not suitable for continuous solvent or fuel exposure. Testing should be done to confirm performance of the adhesives under these conditions. STORAGE AND SHELF LIFE Shelf life is indicated by the "Use Before" date found on the product label. For best results, Dow Corning RTV adhesives should be stored at or below 25°C (77°F). Special precautions must be taken to prevent moisture from contacting these materials. Containers should be kept tightly closed with head or

air space minimized. Partially filled containers should be purged with dry air or other gases, such as nitrogen. Dow Corning heat-cure adhesives should also be stored at or below 25°C (77°C). Containers should be kept tightly closed and kept in cold storage at all times to extend shelf life. PACKAGING In general, Dow Corning adhesives/sealants are supplied in nominal 0.45-, 3.6-, 18- and 200-kg (1-, 8-, 40- and 440-lb) containers, net weight. Not all products may be available in all packages and some additional packages, such as a bladder packs or tubes, may be available for certain coatings and package sizes. LIMITATIONS These products are neither tested nor represented as suitable for medical or pharmaceutical uses. SAFE HANDLING INFORMATION PRODUCT SAFETY INFORMATION REQUIRED FOR SAFE USE IS NOT INCLUDED IN THIS DOCUMENT. BEFORE HANDLING, READ PRODUCT AND MATERIAL SAFETY DATA SHEETS AND CONTAINER LABELS FOR SAFE USE, PHYSICAL AND HEALTH HAZARD INFORMATION. THE MATERIAL SAFETY DATA SHEET IS AVAILABLE ON THE DOW CORNING

PRIMER SELECTION GUIDE Detailed information is available in the Primers data sheet, form number 10-909, available from the Dow Corning website (www.dowcorning.com/electronics) or from Dow Corning Customer Service. Specification Writers: Please contact your local Dow Corning sales office or your Global Dow Corning Connection before writing specifications on these products.
Volatile Organic Content (VOC)4, grams/liter 77/522 723 723 77/521 753 205/591 862 784 681 688

Dow Corning® brand Primer or Adhesion Promoter P5200 Clear1 1200 Clear 1200 Red P5200 Red2 1204 P52043 1205 3-6060 92-023 Sylgard® Prime Coat
1 2

Flash Point, °C (°F) 31 (87) 13 (55) 13 (55) 31 (87) 8 (46) 14 (57) 13 (55) 15 (59) -13 (9) -13 (9)

Special Properties

Colored for easier identification

For Use On Most metals, glass, ceramics and some plastics

For Use With Pigmented two-part addition cure

Most metals, glass and ceramics Film-forming Improves inhibition resistance Most plastics Most plastics and metals Most metals, glass and ceramics

All one-part alcohol cure All All two-part addition cure

P5200 Clear is a low-VOC alternative to 1200 Clear. P5200 Red is a low-VOC alternative to 1200 Red. 3 P5204 is a low-VOC alternative to 1204. 4 The lower VOC value is for states and air quality management districts that have recognized volatile methylsiloxanes as VOC exempt.

12

GLEW EXHIBIT B

Case 5:07-cv-05248-JW

Document 154-3

Filed 05/19/2008

Page 13 of 14

WEBSITE AT WWW.DOWCORNING.COM, OR FROM YOUR DOW CORNING REPRESENTATIVE, OR DISTRIBUTOR, OR BY CALLING YOUR GLOBAL DOW CORNING CONNECTION. HEALTH AND ENVIRONMENTAL INFORMATION To support customers in their product safety needs, Dow Corning has an extensive Product Stewardship organization and a team of Product Safety and Regulatory Compliance (PS&RC) specialists available in each area. For further information, please see our website, www.dowcorning.com, or consult your local Dow Corning representative. LIMITED WARRANTY INFORMATION ­ PLEASE READ CAREFULLY The information contained herein is offered in good faith and is believed to be accurate. However, because conditions and methods of use of our products are beyond our control, this information should not be used in substitution for customer's tests to ensure that Dow Corning's products are safe, effective, and fully satisfactory for the intended end use. Suggestions of use shall not be taken as inducements to infringe any patent. Dow Corning's sole warranty is that the product will meet the Dow Corning sales specifications in effect at the time of shipment. Your exclusive remedy for breach of such warranty is limited to refund of purchase price or replacement of any product shown to be other than as warranted. DOW CORNING SPECIFICALLY DISCLAIMS ANY OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY. DOW CORNING DISCLAIMS LIABILITY FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.

13

GLEW EXHIBIT B

Case 5:07-cv-05248-JW

Document 154-3

Filed 05/19/2008

Page 14 of 14

For More Information To learn more about these and other products available from Dow Corning, please visit the Dow Corning Electronics website at www.dowcorning.com/electronics.

Dow Corning and Sylgard are registered trademarks of Dow Corning Corporation. All other trademarks or brand names are the property of their respective owners. ©2000-2006 Dow Corning Corporation. All rights reserved. Printed in USA
AGP8125

Form No. 10-911F-01 GLEW EXHIBIT B