Free 52561.pdf - Indiana

OAQ PROCESS INFORMATION APPLICATION PI-20: Woodworking & Plastic Machining
State Form 52561 (R / 1-07)

INDIANA DEPARTMENT OF ENVIRONMENTAL MANAGEMENT

IDEM ­ Office of Air Quality ­ Permits Branch 100 N. Senate Ave., MC 61-53 Indianapolis, IN 46204-2251 Telephone: (317) 233-0178, or Toll Free: 1-800-451-6027 x30178 (within Indiana) Facsimile Number: (317) 232-6749 www.idem.IN.gov/permits/air/index.html

NOTES:

· · ·

The purpose of this form is to obtain detailed information about the woodworking or plastic machining process. Complete one form for each process unit (or group of identical process units). This is a required form. Detailed instructions for this form are available online at

www.idem.IN.gov/permits/air/apps/instructions/pi20instructions.doc .
All information submitted to IDEM will be made available to the public unless it is submitted under a claim of confidentiality. Claims of confidentiality must be made at the time the information is submitted to IDEM, and must follow the requirements set out in 326 IAC 17.1-4-1. Failure to follow these requirements exactly will result in your information becoming a public record, available for anyone to inspect and photocopy.

PART A: Process Information Part A identifies the woodworking or plastic machining process. If there are multiple process units that are identical in nature, capacity, and use, you may use one form to summarize the data for the identical process units. 1. Unit ID: 3. How many (identical) process units are identified in this form? 4. Type of Process: 5. Machining Equipment: 6. Capacity Rating (specify units): 7. Grain Loading from the Pneumatic Conveyor Outlet (gr/dscf): 8. Maximum Airflow 9. Normal Airflow
(acfm):

2. Installation Date:
(actual or anticipated)

One Woodworking SHP Planar

More than one (specify number) : Other (specify): Other (specify):

Plastic Machining 10 inch Table Saw

(acfm):

10. Maximum Production Rate (specify units): 11. Control Technology: Identify all control technologies used for this process, and attach completed CE-01 form (unless "none"). None Baghouse / Fabric Filter ­ Attach CE-02. Electrostatic Precipitator ­ Attach CE-04. Wet Scrubber / Absorption ­ Attach CE-05. Other (specify): Cyclone ­ Attach CE-03. Electrostatic Gravel Bed Filter ­ Attach CE-04 Mechanical Collector ­ Attach CE-10 ­ Attach CE-10.

12. Control Techniques: Identify all control techniques used for this process.

13. Process Limitations / Additional Information: Identify any acceptable process limitations. Attach additional information if necessary.

Continued on next page

Page 1 of 2

Indiana Department Of Environmental Management Office Of Air Quality State Form 52561 (R / 1-07)

Process Information ­ Woodworking / Plastic Machining FORM PI-20 Page 2 of 2

PART B: Emission Factors Part B identifies all emission factors used to calculate air emissions from this process. 14. Process Unit
(& ID, if applicable)

15. Air Pollutant

16. Emission Factor
value units

17. Source of Emission Factor
(if not using AP-42, include calculations)

AP-42 AP-42 AP-42 AP-42 AP-42 AP-42

Other Other Other Other Other Other

PART C: Processed Materials Part C identifies the materials machined, the raw materials usage, and the rate of dust production. 18. Materials Machined 19. Raw Materials Usage Rate (lb/hr) 20. Dust Production (lb/hr)

PART D: Federal Rule Applicability Part D identifies any federal rules that apply to the process. 21. Is a New Source Performance Standard (NSPS) applicable to this source?
Attach a completed FED-01 for each rule that applies.

Yes

No

40 CFR Part 60, Subpart

(Specify):

22. Is a National Emission Standard for Hazardous Air Pollutants (NESHAP) applicable to this source? If yes, attach a completed FED-01 if this rule is applicable. 40 CFR Part 61, Subpart 40 CFR Part 63, Subpart
(Specify): (Specify):

Yes

No

23. Non-Applicability Determination: Provide an explanation if the process unit appears subject to a rule (based on the rule title or the source category), but the rule will not apply.